• Engine oil and filter change
• Fuel and water separating filter change
• Check all oil levels, power steering, gear oil reservoir (if Mercruiser)
• Check all drive belts
• Visual check of general engine condition and report
• Run up and check oil pressure, engine temperature, etc.
• Report any further problems or faults to the customer

• Engine oil and filter change
• Fuel and water separating filter change
• Check all oil levels, power steering, gear oil reservoir (if Mercruiser)
• Check all drive belts
• Visual check of general engine condition and report
• Clean and re-set contact breaker gap, spark plugs
• Re-set ignition timing and dwell angle
• Run up and check oil pressure, engine temperature
• If visible, check condition of fuel and tank
• Remove and clean air filter / flame arrester
• Check engine mounted impreller on sea water pump
• Check corrosion protection (anodes) condition if possible
• Report any further problems or faults to the customer

• Engine oil and filter change
• Fuel and water separating filter change
• Check all oil levels, power steering, gear oil reservoir (if Mercruiser)
• Check all drive belts
• Visual check of general engine condition and report
• Run up and check oil pressure, engine temperature, etc.
• If visible, check condition of fuel and tank
• Remove and clean air filter / flame arrester
• Check engine mounted impeller on sea water pump
• Check corrosion protection (anodes) condition if possible
• Replace spark plugs
• Remove and clean distributor cap, check condition
• Replace contact breaker and condensor
• Check H.T. leads
• Re-set ignition timing and dwell angle settings
• Check battery condition
• Check engine breather pipes are free from blockage
• If on dry land check propeller condition and report
• If on dry land check exterior condition of outdrive and report
• Full sea trial
• Report any further problems or faults to the customer

• Engine oil and filter change
• Fuel and water separating filter change
• Check all oil levels, power steering, gear oil reservoir (if Mercruiser)
• Check all drive belts
• Visual check of general engine condition and report
• Run up and check oil pressure, engine temperature, etc.
• If visible, check condition of fuel and tank
• Remove and clean air filter
• Check engine mounted impeller on sea water pump
• Check battery condition
• Check engine breather pipes are free from blockage
• If on dry land check propeller condition and report
• If on dry land check corrosion protection (anodes) condition if possible
• If on dry land check exterior condition of outdrive and report
• Full sea trial
• Report any further problems or faults to the customer

• Remove outdrive
• Check steering linkage
• Change gear oil
• Grease propeller splines and check propeller bush
• Check gear change operation and linkages
• Check outdrive mounted impeller on sea water pump
• Grease U/J joints
• Check oil level in trim reservoir
• Check condition of drive bellows
• Check condition f drive bonding / earthing
• Check condition of drive and transom corrosion protection (anodes)
• Replace outdrive, connect gear change and tilt cylinders
• Test tilt / trim and steering movement
• Report any further problems or faults to the customer

• Check gear box level and oil condition
• Check gear operation and noise
• If possible check oil pressure
• Check coupling bolts are tight and are bonded to earth
• Check gland or deep sea seal for wear
• Check gland or deep sea seal for water leaks
• Check condition of stern tube prop shaft
• If boat is out of water check propeller and cutlass bearing condition
• Check corrosion protection (anodes) condition
• Report any further problems or faults to the customer.

• Oil and filter change
• Check drive belts for condtion and adjust for tension
• Re-assemble water pump impeller
• Run-up engine to temperature

• Re-assemble outdrive to transom shield
• Check anodes
• Check trim / tilt action
• Re-fit propeller

• Remove gearbox and check impeller
• Change gear oil
• Check propeller bush
• Re-assemble gearbox to engine
• Change spark plugs
• Change fuel and water separator filters
• Check throttle and gear linkage cables
• Check batteries
• Check fuel line hoses
• Check tote tank condition
• Check tilt / trim operation
• Grease linkages on throttle and gear linkage cables
• Grease steering and pivot bushes
• Check corrosion protection (anodes) condition
• Run-up engine
• Test operation for idling, gear change and pick-up
• Check general engine condition and report
• Report any further problems or faults to the customer

• Run-up to temperature
• Induce storage seal into carburettor
• Remove spark plugs and induce storage seal into piston bores
• Check gearbox oil
• Remove propellor
• Grease splines and steering cable
• Spray powerhead with corrosion guard

• Clean spark plugs
• Run-up to temperature
• Check and adjust for slow running
• Check anode condition
• Re-fit propeller
• Outboard engine remove or re-fit
• Outboard engine storage

• Price on application

• Price on application

• Check brake operation
• Check ball hitch operation
• Check and re-pack with grease jockey wheel and clamp mechanism
• Check wheel bearings re-pack with grease and adjust
• Check wheel bearing lip seal condition
• Check condition of rollers and side supports
• Check lights and lighting board
• Report any further problems or faults to the customer

• Length up to 8 metres (LOA)
• Price on application

EQUIPMENT STORAGE

• Outdrive
• Price on application

• Price on application

• Price on application

• Price on application